banner
 
  Home >> Blogs

this user is offline now  kokoele
Send message

Subscribe



Categories:

Archive:
October 2020
September 2020
August 2020
July 2020
June 2020
May 2020
April 2020
March 2020
February 2020
January 2020
December 2019
November 2019
October 2019
September 2019
August 2019
July 2019
June 2019
May 2019
April 2019

Who Gives Kudos:



 

  

Tap Filter & Shower Filter Installation Precautions

With the development, water pollution has become more serious now, bringing a lot of harm to everyone's body, so many people now buy pure water to drink, but the kitchen and bathroom water is generally tap water, so now on the market, There are Tap Filter & Shower Filter(KOKOELECTRIC). Let's talk about how to install the faucet and how to install the faucet. Let's talk to you.

First, how to install the filter tap

1. Old-fashioned faucet filter. To close the sluice switch, in order to prevent the faucet filter from falling out, it should be inserted into the bottom of the faucet filter.

2. New faucet filter. Close the water switch, then remove the filter cover on the faucet, then insert the coupling into the faucet, then connect the faucet filter to the coupling, and then secure it.

Second, the faucet installation precautions

1. Installation of single hole basin faucet

When installing, be sure to choose a special angle valve, and the angle valve must be fixed with the hot and cold water pipe of the wall outlet. When you find a distance between the angle valve and the water pipe on the faucet, purchase a special extension tube to connect. Remember, don't use other water pipes to connect, because if the water pressure is too large, it will easily fall off and leak, causing damage to you. If the inlet pipe is too long to exceed the outlet pipe, you can cut off the part according to your needs. If the angle is not suitable, bend it to the position you need as needed. Remember: Do not bend hard to 90 degrees or more than 90 degrees. When installing the basin to remove water, please don't forget to buy the small interface of the faucet (the faucet is shorted). Don't forget to flush the water pipes buried in the wall before you install it.

2, shower, bathtub faucet (wall mounted) installation

When you have purchased a shower, bathtub, or wall faucet, you can choose the right height to bury the water pipe. The spacing between the hot and cold water pipes must be 15 cm. Before installation, you must not forget to flush the water pipe to avoid excessive water quality and damage to the faucet.

Concealed shower, bath faucet: After purchasing the concealed faucet, the sump's spool should be pre-buried in the wall. Be sure to pay attention to the thickness of the bathroom wall before embedding. If the wall is too thin, the spool will not be buried. The plastic protective cover of the valve plug should not be easily removed when it is buried, so as to prevent the cement and other chores from damaging the valve core when it is buried. In addition, when pre-burying the valve core, you should also pay attention to the up and down and left and right directions of the valve core to avoid the valve core being buried. When the wall mounted faucet is pre-buried into the water pipe, the size is deviated, and the adjustment can be used to adjust the position.

3, the installation of thermostat

Before installing the thermostatic faucet, please check if the water pipe is left hot and cold right. Remember not to connect the hot and cold water pipes incorrectly, so as to prevent the faucet from working properly. Gas and solar water heaters cannot use thermostats because the water pressure is too low. Please install the thermostatic faucet and don't forget to install the hot and cold water filter.

4, single hole kitchen faucet installation

The requirement is stable, because the kitchen faucet is used frequently, and it is moved and moved, so it is easy to loosen, so the lock nut must be tightened.

The above is the introduction to the installation of the faucet and the faucet installation precautions. The faucet has different installation methods according to the use of different functional areas in the home. The kitchen and bathroom, as well as the bathroom shower, basin, thermostat, etc., need to be differentiated by the consumer in advance, and the corresponding faucet installation is purchased.

Click Water Dispenser Tap & Faucet to learn about more information.

Mood: Tap Filter & Shower Filter
- 0 Comments - 0 Kudos - Add comment 
 
|
|
|
|
|
 
Copyright © 2009 - 2012 True2ourselves. All rights reserved.
Reproduction in whole or in part in any form or medium without express written permission is prohibited.